Car Stereos: Amp Subwoofer and standard speakers, ohm voice coils, watts rms

Question
I would like to know would this be a compatible system as far as subwooder to amp and standard speakers to amp. Here is my setup.

Amp for subwoofers is Alpine MRP-M1000 •mono subwoofer car amplifier
•600 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms)
•variable low-pass filter (50-200 Hz, 24 dB/octave)
•variable bass boost (0-12 dB at 50 Hz)
•subsonic filter (15 Hz, 24 dB/octave)
•Class D amp with MOSFET power supply
•CEA-2006 compliant
•STAR Topology (minimizes internal noise and prevents ground interference)
•speaker- and preamp-level inputs
•gold-plated screw terminals
•fuse rating: 25A x 4
•4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
•15"W x 2-7/16"H x 9-9/16"D

2 Alpine SWR-1222D TYPE R 12" subwoofer with dual 2-ohm voice coils
Kevlar® reinforced pulp cone with Santoprene™ rubber surround
cast aluminum frame with perimeter venting
frequency response: 23-500 Hz
power handling: 200-500 watts RMS (250 watts per coil)
peak power: 1,500 watts
sensitivity: 85 dB
top-mount depth: 7-5/8"
sealed box volume: 0.57-1.0 cu. ft.
ported box volume: 0.75-2.0 cu. ft.\

Amp for standard speakers is Alpine - 200W Class A/B Bridgeable 4/3/2-Channel MOSFET Amplifier w/ Adjustable Crossover

200W peak power (50W x 4) @ 4 ohms, 14.4V, 20Hz - 20kHz, 1% THD
150W x 2 RMS (continuous) power @ 4 ohms, bridged
50W RMS (continuous) power x 4 @ 4 ohms, 14.4V, 20Hz - 20kHz, 1% THD
75W RMS (continuous) power x 4 @ 4 ohms, 14.4V, 20Hz - 20kHz
MOSFET power supply delivers clean power with minimal heat dispersion; rugged heat sinks and thermal management processor regulate amp temperature to help prevent overheating; overcurrent protection
Adjustable high-pass/low-pass crossover
EQ and bass EQ controls for customizable audio; continuously adjustable gain control
Discrete preamp stage
Gold-plated RCA inputs; speaker level inputs; nonfading preamp output
Top-mounted blue LED power/status indicator
STAR circuitry
Impedance: 2 or 4 ohms
Signal-to-noise ratio: 100dBA

Standard speakers are 2 for front and 2 for back(4 total)

2 sets of Alpine - 6-1/2" 2-Way Coaxial Car Speakers (Pair)
Model: SPR-17C
Compatible with MRP-F250 and MRP-F450 amplifiers
Handles up to 300 watts peak power (100 watts RMS)
Hybrid layered-pulp woofers with mica cones, linear drive motors and roll rubber surrounds offer full, deep bass
1" swivel-ring tweeters deliver crisp highs
Aluminum baskets with integrated tinsel leads
Strontium magnets
Sensitivity: 87dB
Impedance: 4 ohms

So does this sound like a good setup and will this get all the power it needs to the speakers and subwoofers and how should i wire it.

Answer
Yes, It sounds like a really good setup.  The power is properly matched for both sets of speakers.  I would series wire the dual voice coils together.  Then wire each sub to each channel on the amp.  The gain of the sub amp may need to be adjusted down just a bit, but should sound great.  Hope this helps, Scott