QuestionHow to i remove door panel, original motor and regulator and put the new one
in? it is on the front passenger side. also which fuse is for the cruise controle i
am having problems to where i can turn it on and then i hit the set button and it
turns on or stays on but doesnt set.
Answerthere is no fuse for the speed control
FRONT DOOR TRIM PANEL
REMOVAL
CAUTION: Do not pry on door trim panel, damage to trim panel will result.
1.Remove speaker flag.
2.Remove speaker grille by inserting trim tool at the rear of the grille and disengaging clips holding to trim panel. Remove grille Front Door Trim Panel - Typical
3.Remove trim plug from the pull cup and remote bezel by inserting a small flat blade tool into the notch and remove.
4.Remove three screws from bottom of door.
5.Remove screw in pull cup.
6.Remove screw in remote bezel.
7.Remove two screws in the instrument panel interface area.
8.Remove three screws in the speaker area.
9.Using an trim tool, disengage the retainer clips from the door trim panel to the door panel.
10.Raise trim panel up to disengage from the belt being careful to hold the panel securely.
11.Disconnect the linkage from the remote handle assembly Inner Front Door Trim Panel - Typical
12.Disconnect the power mirror switch.
13.Disconnect the power door lock switch wire connector.
14.Disconnect the power window switch wire connector.
15.Disconnect the radio speaker wire connector.
16.Disconnect wiring harness clips from trim panel.
17.Disconnect the courtesy lamp.
18.Remove trim panel from vehicle.
INSTALLATION
1.Place door trim panel in position.
2.Install wire harness clips into door trim panel.
3.Connect the courtesy lamp.
4.Connect the radio speaker wire connector.
5.Connect the power window switch wire connector.
6.Connect the power door lock switch wire connector.
7.Connect the power mirror switch wire connector.
8.Connect the linkage to the handle assembly.
9.Install the water shield. Ensure that the water shield locator holes align. Ensure that the shield is sealed.
10.Insert trim panel into channel retainer at top door.
11.Insert the forward four way alignment guide into position. Insert the rearward two way alignment guide into position.
12.Install new retaining clips to attach door trim panel to door panel.
13.Install three screws in the speaker area.
14.Install two screws in the instrument panel interface area.
15.Install screw in the remote bezel.
16.Install screw in pull cup. Tighten screw to 1.7 to 2.3 N·m (15 to 20 in. lbs.) torque.
17.Install three screws to the bottom of the door. Tighten screws to 1.7 to 2.3 N·m (15 to 20 in. lbs.) torque.
18.Install pull cup and remote bezel trim plug, if equipped.
19.Place speaker grille in position on trim panel. Attach door speaker clip
FRONT DOOR GLASS REGULATOR
REMOVAL
1.Remove flag cover, door trim panel, water shield as necessary, and pull cup support bracket.
2.Slide glass from regulator roller channel.
3.Disconnect power window motor wire connector.
4.Loosen bolt attaching regulator support brace to door panel.
5.Remove screw and bolt heads from keyhole slots in door panel.
6.Loosen bolts attaching regulator to door panel.
7.Remove regulator from door panel.
8.Slide regulator rearward and rotate forward end of roller channel through access hole in door panel Window Regulator
INSTALLATION
1.Insert roller channel through access hole in door panel.
2.Insert bolt heads on regulator through key hold slots in door panel.
3.Tighten bolts attaching regulator to door panel.
4.Tighten bolt to attach regulator support brace to door panel.
5.Tighten screw to attach regulator scissor channel to door panel.
6.Connect power window motor wire connector.
7.Lower door glass on to regulator roller channel.
8.Align glass and verify operation.
9.Install pull cup support bracket, water shield, door trim panel and flag cover.
