Small Engines (Lawn Mowers, etc.): 1985 John Deere 1032 snowblower, john deere snowblower, blue flames

Question

inside exhasut port I recently acquired an older john deere snowblower, model # M01032X538828.  It has a 10 hp tecumseh engine on it.  It starts and runs great, but when I engage the auger drive it struggles and sputters and sometimes dies.  I took apart and cleaned up the carb.  The spark plug was covered in black soot looking build up. I replaced it and the new one is accumulating it.  I have attempted to adjust the carb to lean it out but it doesn't appear to help.  It tends to backfire (or actually afterfire I guess)out the exhaust.  The muffler gets red and when removed it intermittently shoots blue flames and pops out the exhaust port.  
I have been advised to run some Seafoam through it which i have done in a very small quantity.  That plus the carb cleaning seems to have helped as it does run better, but am curious about what else can be done as I don't think it is completely fixed.  Whether I need to run something through it or take it further apart to clean it; please let me know your professional opinion.
The gentleman I got it from like to run it on 1/2 choke all the time I think too.
I have attached a picture of inside the exhaust port with the muffler removed.  Not exactly sure what it is.. but it definitely has a build up on it.
Thanks,
Rich - getting ready for snow!


Answer
Hello Rich:

You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, http://jdpc.deere.com/jdpc/servlet/com.deere.u90490.partscatalog.view.servlets.H... and Enter the Model Numbers 1032 and Click Find. Then Select your Model from the Search Results Area. Then Select the Sectional File. Then Select the Section of the Mower you Wish to View Online. From your Description I Suggest you; 1- Check the Flywheel Key. If this Key is Damaged, you will have the Problem you Described. The Following is the Instruction File I Made for Removing the Flywheel from Most Mower Engines.  It is the Basics and if you have a Question, Please Ask. Any Input to Make this File Better is Appreciated. ***Disconnect the Coil Wire from the Spark Plug. Remove the Blower Housing (metal engine cover). Remove the Coil. Remove the Flywheel Nut or Starter Cup (Depends on the Model). Now Attach a Steering Wheel Puller to the Flywheel Using the Threaded Holes in the Flywheel. Tighten the Puller. Now Hit the Puller with a Hammer. Repeat this Procedure Until the Flywheel Pops Up or can be Lifted Off the Crankshaft. On Some Models you Can Not Use a Puller and Must Use a Pry Bar and a Pipe Cap that is Slightly Larger than the Crankshaft. Place the Pipe Cap Over the Crankshaft to Protect it. Place the Pry Bar Under the Thick Section of the Flywheel and Pull Up Against the Flywheel. **BE CAREFUL  DO NOT PUT A HOLE IN THE BLOCK UNDER THE FLYWHEEL** Now Hit the Pipe Cap that is on the Crankshaft (covered with the Pipe Cap). Repeat the Procedure Until the Flywheel can be Lifted Off the Crankshaft. *** Be Sure you have the Flywheel Torqued to the Proper Torque (I require the Model and Spec/Type Numbers Off the Engine to Provide the Proper Torque) and Set the Coil Gap to .020in.. 2- If the Flywheel Key is Good, then Check the Valve Clearances.  The Following is a Basic Instruction File for Setting the Valve Clearances on Non OHV Engines. Any Input is Appreciated. On this Model Engine I Usually Suggest Reseating the Valves if the Valve Clearance Requires Adjusting. The Following is a General Instruction File for Setting the Valve Clearance on Non OHV Engines. **Remove the Carburetor and the Crankcase Breather/Vent and the Valve (Stem) Cover so you have Access to the Valve Stems, Springs and Keepers. Set 1 Cylinder to TDC on the Compression Stroke. Using a Blade Style Feeler Gauge, Check the Clearances. The Intake should be .005in - .007in and Exhaust .008in - .010in. If the Feeler Gauge will Not Slide Between the Valve Tip and the Tappet, then you Must Reset the Clearances. **You Will Require a Small Engine Valve Spring Compressor to Remove the Springs and Keepers from the Valve Stems.** Some Engines Use a Valve Keeper that is like Automotive Keepers (2 Cone Shaped Keepers that Set in the Valve Retainer/Rotocoil Assembly)and the Other Style is a Slotted Retainer that is Moved (once the Valve Spring is Compressed) to the Larger Opening in the Retainer and the Retainer Slips Over the Valve Stem Tip for the Valve to be Removed. Remove the Heads. Set 1 Cylinder so the Piston is at TDC on the Compression Stroke And Check the Clearances Between the Valve Stem Tip and the Tappet. The Clearances are as Follows: Intake Valve Clearance is .005in - .007in and the Exhaust is .008in - .010in. You have to Lightly Grind the Valve Stem Tip and Place the Valve Back Into the Engine (you can Hold the Valve Seated by Hand) and Check the Clearance Until you Reach the Required Clearances. **++** For this Engine Model I Suggest you Reseat the Valves while you are Setting the Correct Valve Clearance. For this you will Need a Small Valve Seat Suction Tool. This can Usually be Purchased for $10.00us and has a Suction Cup that Hold the Valve Head so you can Turn the Valve Back and Forth and Dress up the Valve Seat. Valve Grinding Compound is Approximately $5.00us a Tube and a Tube Last the Shop About a Year. It Doesn't Take a Lot to Reseat 1 Engine.**++** Once the Valve Clearances are Reached and the Valve Seat is Nice and Dull; Re-Install the Valves on that Cylinder and Turn the Other Cylinder to TDC on the Compression Stroke and Set that Cylinders Valve Clearances.  Once that Cylinder is Set, then Re-Assemble the Engine.** If you Hit a Snag or this Does Not Correct the Problem,  I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. Have a Happy Holiday Season and May the All Mighty Bless You and Yours. Be Safe and Happy. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Comments and Ratings are Greatly Appreciated. Thanks.

Respectfully

John