Small Engines (Lawn Mowers, etc.): cub with lack of power, crankcase oil, internal passages

Question
I have a cub cadet lt 1046. motor: cv23s-75593 ser: 3421423861
manf 11/09/04.
I have a loss of power, it will idle ok feels a little rough but at full throttle you can tell by sound it is not right and when you engage the pto you can really tell. The mower has 63 hrs only, I checked the plugs blackish and damp? Gas?  I suspect carb needs cleaned as I thought I emptied fuel but didn't and there was no stay-bil added. (wont happen again) I sprayed some gumout carb cleaner into it but wasn't to sure how to remove carb or if I should (been about 18yrs since I played with a carb) I am hoping it is a minor problem as I have had a valve keeper come off at 35hrs and bust thru the valve cover.(cub covered repair after calender warrantee but hrs were so low). I thought about buying some car fuel tank additive to clean carbs? good or bad Idea?  The deck is clean and the bearings lubed,so I doubt that is it .  Ok i'll shut up now and let the expert talk
Thank You
kurt

Answer
Hello Kurt:

LOL. Thanks for Using All Experts. From your Description it Sounds like the Carburetor Float Needle Valve is Not Seating Correctly. Is the Crankcase Oil Contaminated with Gas? I Suggest you Disassemble and Clean the Carburetor. Spray Carburetor Cleaners and the Gas Additives do Not Really Perform Well for Cleaning Carburetors on Small Engines. Most Homeowners can Use a Breakdown and Disassemble, Clean and Assemble these Carburetors. You can View a Breakdown of the Engine at this Site Addy; http://www.kohlerplus.com/login.asp and Select Enter as Guest. Now Select the Thumbnail of the Engine Catalog you Wish to View. The Following is a General Instruction File for Carburetor Cleaning. Even though the Carburetor Looks Clean, the Internal Passages May be Restricted with Varnish that Gas Causes to Build Up over Time. I Suggest you Make Sure the Gas is Free Flowing to the Carburetor Inlet Port. If the Gas is Free Flowing to the Inlet Port, then  **Remove, Disassemble and Soak the Carburetor Overnight in Carburetor Cleaner (I Use Gunk). I have Found that Most People can Use a Breakdown/IPL and Disassemble the Carburetor Enough for Proper Cleaning. You Only have to Remove the Bowl (if Applicable), Float Pin (if Applicable), Float (if Applicable), Needle Valve and Needle Valve Seat if Applicable. This is a Flat O-Ring Located in the Inlet Port the Float Needle Rests in. Use a Strong Wire with a Slight Bend to Remove the Old Seat. Sometimes a Small Pocket Screw Driver can be Use Also. The New Seat will have a Slightly Beveled Side and a Flat Side. The Flat Side goes Towards the Carburetor Body when Inserted into the Inlet Port. Spray the Seat with Spray Lubricant to make Installation Easier. The End of a Drill Bit that is Slightly Small than the Seat can be Use as an Insertion Tool. Wear Gloves or Use a Rag when Handling the Sharpened End of the Drill Bit. Remove Any Adjustment Screws that Go Into the Carburetor Body. The Welch Plugs Do Not have to be Removed. Then Soak the Carburetor Body and Parts in a 1 Gallon Can of Gunk Carburetor Cleaner Overnight. The Can has a Parts Tray Inside it for the Small Parts. Once the Carburetor and Parts are in the Cleaner, you can Replace the Lid for Safety and to Prevent Accidental Spillage. Then Blow Out the Passages with Compressed Air.*** (Do Not Use High Pressure Air for the Zama Carburetors, they have Check Valves for the Primer and these are Usually Blown Out of the Carburetor if Not Careful. Allow the Zama Carburetor to Set on a Drip Pan and Dry)***. ****All the Carburetor Adjustments are the Same for Lawn Mower and Trimmers. There are Several Location for the Air Mixture Screws. The Idle Air Mixture Screws are Usually Located at the Top of the Carburetor Bowl and the Top of the Carburetor Body. If the Main Air and Idle Air Mixture Screws are Side by Side on the Side of the Carburetor, then the Idle Air is the Farthest from the Engine. The Main Jet Air Mixture Screw is Located in the Bottom of the Carburetor Bowl or Beside the Idle Air Screw on the Side of the Carburetor Body. Some of the Older Model Carburetors have the Main Jet Mixture Screw Straight in from the Top of the Carburetor Body (this is Rare anymore). If you have Cleaned the Carburetor (Disassembled and Soaked Overnight in Carburetor Cleaner (I Use Gunk). Then Blow Out the Passages with Compressed Air and Install a New Kit if Required. Now Setting the Air Mixture Screws:  ****Turn the Idle Air and Main Air Mixture Screws In Until SNUG **Do Not Jam** Then Reverse Both Screws 1 1/2 Turns. Holding the Throttle Full Open, Start the Engine. Turn the Main Air Mixture Screw Clockwise Until Proper Revs are Obtained. Occasionally you May have to Turn this Counter Clockwise to Achieve the Proper Revs. Now Allow the Engine to Idle. Set the Engine Idle Screw (Not Idle Air) so the Engine will Stay Running if Required. Now Set the Idle Air Mixture Screw so there is No Hesitation when Throttling from Idle to Full Throttle. Reset the Engine Idle if Required.**** If This Carburetor has a Single Air Adjustment. Use the Section Above that Pertains to Full Throttle RPM Air Mixture Screw and then Adjust the Screw if Required to Eliminate Any Hesitation when Throttling from Idle to Full Throttle. This file was Intended to Give you the Basic Carburetor and May Not Reflect Yours. If you have Questions, Please Ask. If you Hit a Snag or this Does Not Correct the Problem,  I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Thanks.

Respectfully

John