Small Engines (Lawn Mowers, etc.): No juice, using jumper cables, switch jumper

Question
I have a 2000 White LT1300. Took it out of storage and tried to start. Battery low or dead. tried jump starting.
Still no juice. Can't even light the tiny headlights w/ key on. Only sound it a click when you turn the key.
Jumper cables are good. Any thoughts where to begin?

Answer
Hello Mark:

Charge the Battery. If Using Jumper Cables Make Sure you have a Good Connection at the Battery Posts of Both Batteries. Check the Starter and Solenoid. **(with the Spark Plug/s Removed) To Check the Solenoid and Starter, Once you are Sure the Battery is Fully Charged/New, then Use your Jumper Cable Set and Attach the Positive Lead Onto the Positive Post of the Battery (make sure the Battery is Fully Charged or is a New Battery). Now Firmly Touch the Large Post on the Starter. If the Starter Does Not Turn and you can turn the Engine by Hand, then the Starter is Bad. If the Starter Turns the Engine Properly, Then Check the Solenoid. Firmly Touch the Small Post at the Base of the Solenoid that has the Ign Wire Attached to it. If The Starter Does Not Turn and the Solenoid Clicks, Then the Solenoid is Bad.** If the Starter and Solenoid are Good, then Check the Safety Switches. **PLEASE REMEMBER THAT THE INSTRUCTIONS FOR CHECKING THE SAFETY SWITCHES IS JUST THAT!!! FOR CHECKING ONLY. I NEVER Suggest a Mower be Operated with a Safety Device or Switch Disconnected or Bypassed. Now. On Some Model Mowers you can Simply Unplug the Safety Switch from the Harness. On Other Models you have to Place a Jumper Wire Between the Harness Terminals (on the 4 Post Switch Jumper from Same Color Wire to Same Color Wire). Check the Clutch/Break and the Blade/PTO Safety Switches First. Check the Seat Safety Last. Usually the Seat Safety is Not in the System for Starting the Engine. Just to Ensure Someone is in the Seat when Engaging the Transaxle and/or Blades.** On Some Model Mowers, the Lights will Not Function Until the Engine is Running. Send me the Model Numbers Off the Mower, Please. With these I can Locate the Proper Manual and Better Assist you. The LT1300 is the Series Model. White is an MTD Mower Using the White Name. For Help Locating the Model Numbers: Generally the identification tag is on a part of the unit that, even after years of use, rarely needs replacement. For most of MTD power equipment, these tags are approximately 2" by 3" in size. They also have the MTD Products name, address and customer service phone number listed across the bottom. For hand held product, the tag is normally white and approximately 1" by 1/2" in size. Hand held i.d. tags are normally on an aluminum portion of the engine, somewhat set into the unit to protect the label from wear. (A bar code will also be on this tag.) Riding mower tags are located on the underside of the seat. For walk behind mowers this tag is found either on the deck or on the rear door of rear discharge units. Tiller model and serial tags are generally on the tine housing. **The model and serial tags for two-stage snow throwers are located on the bottom of the main gear housing which is often called the belly pan, while single stage snow thrower tags are next to the key and primer. For other products like log splitters, chipper shredders and edgers, tags can be found on the frame or main housing.** If you Hit a Snag or this Does Not Correct the Problem,  I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Thanks.

Respectfully

John