Small Engines (Lawn Mowers, etc.): my 15 hp ohv briggs and stratton is putting, briggs and stratton, adjustment screws

Question
QUESTION: on my craftsman tractor i have a 15 hp ohv briggs and stratton  
.when i start my tractor the engine will not idle correctly so it putts and eventually shuts off i tried to replace the spark plug but that did nothing i also took the bowl off the carb to see if it was dirty in it but it was not what do u think is wrong with it?

ANSWER: Hello Pat:

Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the Proper Manual and Better Assist you. The Model Numbers May be Stamped Into the Blower Housing (metal engine cover) Above the Spark Plug. Depending on the Model: 1- It could be the Carburetor Solenoid is Not Opening Correctly and Restricting the Gas Flow to the Carburetor Jet. **If the Carburetor Shut Off Solenoid has Current, then Remove the Carburetor Solenoid and Go to the Hardware Store. Purchase a Bolt of the Same Diameter and Threads. It Needs to be 3/4" Long. Put this Bolt in Place of the Solenoid. If this Corrects the Engine Problem, then Replace the Solenoid. ***NOTE: THIS IS FOR CHECKING THE SOLENOID ONLY I NEVER SUGGEST YOU OPERATE THE ENGINE WITH THE SOLENOID OUT OF THE CARBURETOR EXCEPT FOR TESTING PURPOSES*** Sometimes the Plunger is Moving, Just Not Far Enough to Allow the Gas to Enter the Jets.** 2- The Carburetor Could have a restricted Jet and Require Soaking and Cleaning. **Remove, Disassemble and Soak the Carburetor Overnight in Carburetor Cleaner (I Use Gunk). I have Found that Most People can Use a Breakdown/IPL and Disassemble the Carburetor Enough for Proper Cleaning. You Only have to Remove the Bowl (if Applicable), Float Pin (if Applicable), Float (if Applicable)  and Needle Valve and Any Adjustment Screws that Go Into the Carburetor Body. The Welch Plugs Do Not have to be Removed. Then Soak the Carburetor Body and Parts in a 1 Gallon Can of Gunk Carburetor Cleaner Overnight. The Can has a Parts Tray Inside it for the Small Parts. Once the Carburetor and Parts are in the Cleaner, you can Replace the Lid for Safety and to Prevent Accidental Spillage. Then Blow Out the Passages with Compressed Air. Install New Parts if Required.** The Valve Clearance May Require Resetting. I Do Not Use the Setting Called for by the OEMs. I have Found that the Following Works Best. Remove the Valve Cover (on the Dead Cylinder for Twin Cylinder Engines). Set the Cylinder you are Setting the Valves on to Top Dead Center (Both Rocker Arms will have Play in them when the Engine is at TDC) When Setting the Valve Clearance. Now Loosen the Valve Adjuster Locks and Set the Intake Valve Clearance to .004in -.006in and the Exhaust to .007in - .009in. I have had Better Performance Out of the Mowers and Less Burnt Valves Using these Settings. Be Sure the Piston is at TDC on the Compression Stroke. If you Hit a Snag or this Does Not Correct the Problem,  I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Thanks.

Respectfully

John

---------- FOLLOW-UP ----------

QUESTION: my model # is 28n707

Answer
Hello Again Pat:

You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.smallenginepartswarehouse.com/parts.asp and Select the Shop Online Parts Look Up. Then Select the Model Tab. Then Select the OEM and Enter the Model (5 or 6 Digits) and Type Numbers (first 4 digits Only). Example: 28N707-????. Then Double Click on the Model in the Results Area. Now you can Select the Section of the Engine you Wish to View. If the Starter is Turning the Engine Correctly when Starting and the Engine is Idling Rough and Can Not Rev Properly, then First  **Remove, Disassemble and Soak the Carburetor Overnight in Carburetor Cleaner (I Use Gunk). I have Found that Most People can Use a Breakdown/IPL and Disassemble the Carburetor Enough for Proper Cleaning. You Only have to Remove the Bowl (if Applicable), Float Pin (if Applicable), Float (if Applicable)  and Needle Valve and Any Adjustment Screws that Go Into the Carburetor Body. The Welch Plugs Do Not have to be Removed. Then Soak the Carburetor Body and Parts in a 1 Gallon Can of Gunk Carburetor Cleaner Overnight. The Can has a Parts Tray Inside it for the Small Parts. Once the Carburetor and Parts are in the Cleaner, you can Replace the Lid for Safety and to Prevent Accidental Spillage. Then Blow Out the Passages with Compressed Air. Install New Parts if Required.** Just because the Bowl is Clean Looking, Does Not Mean the Internal Passages of the Carburetor are Clear. The Most Common Cause of the Problem you Described is the Carburetor and then the  Valve Clearance. If you Hit a Snag or this Does Not Correct the Problem,  I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Thanks.

Respectfully

John