Small Engines (Lawn Mowers, etc.): 5hp briggs runs rough, hp briggs, adjustment screws

Question
I have a 5 hp Briggs on a tiller.  I just got it.  I removed the tank and clean, and sprayed off the carb.  I can get it to run but if dies out and then comes back.  Then it may run for 2 min good then dies out and runs bad for 2 min and then is good again.  Could this just be a carb adjustment needed?  Tank had some junk in it when I got it but I spent sometime on cleaning that good.
Any help would be great..... wife wants the garden tilled!!

Thanks
Eric


Answer
Hello Eric:

Make Sure the Gas is Free Flowing to the Carburetor Inlet Port. Send me the Model and Type or Spec Numbers Off the Engine and the Model Numbers Off the Tiller, Please. With these I can Locate the Proper Manuals and Better Assist you. However, from your Description, it Sounds like you Need to  Remove, Disassemble and Soak the Carburetor Overnight in Carburetor Cleaner (I Use Gunk). I have Found that Most People can Use a Breakdown/IPL and Disassemble the Carburetor Enough for Proper Cleaning. You Only have to Remove the Bowl, Float Pin, Float and Needle Valve and Any Adjustment Screws that Go Into the Carburetor Body. The Welch Plugs Do Not have to be Removed. Then Soak the Carburetor Body and Parts in a 1 Gallon Can of Gunk Carburetor Cleaner Overnight. The Can has a Parts Tray Inside it for the Small Parts. Once the Carburetor and Parts are in the Cleaner, you can Replace the Lid for Safety and to Prevent Accidental Spillage. Then Blow Out the Passages with Compressed Air. Install New Parts if Required. The Following is Instructions for Setting the Air Mixture Screw (if Any). ****All the Carburetor Adjustments are the Same for Lawn Mower and Trimmers. There are Several Location for the Air Mixture Screws. The Idle Air Mixture Screws are Usually Located at the Top of the Carburetor Bowl and the Top of the Carburetor Body. If the Main Air and Idle Air Mixture Screws are Side by Side on the Side of the Carburetor, then the Idle Air is the Farthest from the Engine. The Main Jet Air Mixture Screw is Located in the Bottom of the Carburetor Bowl or Beside the Idle Air Screw on the Side of the Carburetor Body. Some of the Older Model Carburetors have the Main Jet Mixture Screw Straight in from the Top of the Carburetor Body (this is Rare anymore). If you have Cleaned the Carburetor (Disassembled and Soaked Overnight in Carburetor Cleaner (I Use Gunk). Then Blow Out the Passages with Compressed Air and Install a New Kit if Required. Now Setting the Air Mixture Screws:  ****Turn the Idle Air and ****Main Air Mixture Screws In Until SNUG **Do Not Jam** Then Reverse Both Screws 1 1/2 Turns. Holding the Throttle Full Open, Start the Engine. Turn the Main Air Mixture Screw Clockwise Until Proper Revs are Obtained. Occasionally you May have to Turn this Counter Clockwise to Achieve the Proper Revs. Now Allow the Engine to Idle. Set the Engine Idle Screw (Not Idle Air) so the Engine will Stay Running if Required. Now Set the Idle Air Mixture Screw so there is No Hesitation when Throttling from Idle to Full Throttle. Reset the Engine Idle if Required.**** You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.smallenginepartswarehouse.com/parts.asp and Select the Shop Online Parts Look Up. Then Select the Model Tab. Then Select the OEM and Enter the Model and Type Numbers. Then Double Click on the Model in the Results Area. Now you can Select the Section of the Engine you Wish to View. Hope this Helps. I am Here if You Require More Assistance. Let me Know What Happens, Please. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 9pm EST (US). My New Day Starts then. Thanks.

Respectfully

John