QuestionJohn,
I have a 8.5 HP B&S engine (Mod#15A114 Spec-0342 E1) that backfires alot and sometimes just dies all together. I've cleaned the carb and changed the spark plug. I've also checked spark and its ok. I think it might need a valve adjustment. Can you confirm that and maybe explain how to adjust this OHV engine?
Thank you!
Jim
AnswerHello Jim:
>>You can View a Breakdown/IPL of the Engine at this Site Addy; http://www.briggsandstratton.com/engines/support/operators-manuals/ and Enter the Model Numbers and the Type Numbers(15A114-0342-E1) in the Appropriate Box (Find Operators Manuals) and Click GO. Then Select "Illustrated Parts List" (for your Language) from the List of Manuals Shown.
>>Was the Carburetor been Soaked when Cleaned?
>>Has the Flywheel Key been Checked for Damage?
>>The Following is the Instruction File I Made for Removing the Flywheel from Most Mower Engines. It is the Basics and if you have a Question, Please Ask. Any Input to Make this File Better is Appreciated. ***Disconnect the Coil Wire from the Spark Plug. Remove the Blower Housing (metal engine cover). Remove the Coil. Remove the Flywheel Nut or Starter Cup (Depends on the Model). Now Attach a Steering Wheel Puller to the Flywheel Using the Threaded Holes in the Flywheel. Tighten the Puller. Now Hit the Puller with a Hammer. Repeat this Procedure Until the Flywheel Pops Up or can be Lifted Off the Crankshaft. On Some Models you Can Not Use a Puller and and the Jaws of a Standard Puller will Not Fit. On these Type Engines you can Use a Pry Bar and a Pipe Cap that is Slightly Larger than the Crankshaft. Place the Pipe Cap Over the Crankshaft to Protect it. Place the Pry Bar Under the Thick Section of the Flywheel and Pull Up Against the Flywheel. **BE CAREFUL DO NOT PUT A HOLE IN THE BLOCK UNDER THE FLYWHEEL** Now Hit the Pipe Cap that is on the Crankshaft (covered with the Pipe Cap). Repeat the Procedure Until the Flywheel can be Lifted Off the Crankshaft. *** Be Sure you have the Flywheel Torqued to the Proper Torque (I require the Model and Spec/Type Numbers Off the Engine to Provide the Proper Torque) and Set the Coil Gap to .020in..
>>The Following is a Basic File I made for Setting the Valve Clearances. Any Input is Appreciated.
>>**I Do Not Use the Setting Called for by the OEMs. I have Found that the Following Works Best.
>>Remove the Valve Cover (on the Dead Cylinder for Twin Cylinder Engines).
>>Check the Push Tubes and make Sure they are Not Bent.
>>Set the Cylinder you are Setting the Valves on to Top Dead Center on the Compression Stroke When Setting the Valve Clearance. Now Loosen the Valve Adjuster Lock and Using a Blade Style Feeler Gauge, Set the Intake Valve Clearance to .004in -.006in and the Exhaust to .004in - .006in. Loosen and Tighten the Rocker Arm and the Feeler Gauge is Placed Between the Rocker Arm and the Valve Top where the Rocker Arm Pushes on the Valve.
>>***BE SURE TO TIGHTEN THE ADJUSTER LOCK AFTER YOU HAVE THE PROPER VALVE CLEARANCE***
>>I have had Better Performance Out of the Mowers and Less Burnt Valves Using these Settings. Be Sure the Piston is at TDC on the Compression Stroke.**
>>If you Remove the Valve Cover and then Turn the Engine by Hand, you can Watch the Intake Valve Movement. When the Intake Valve Closes, the Piston will Just Starting the Compression/Power Stroke.
>>If you Hit a Snag or this Does Not Correct the Problem, I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. Have a Happy Holiday Season and May the All Mighty Bless You and Yours. Be Safe and Happy. Thanks.
Good Luck
Respectfully
John
PS: I am Allowed to Answer 3 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Follow Up Questions are Received Anytime. Comments and Ratings are Greatly Appreciated. Thanks.
Respectfully
John
