QuestionQUESTION: The steel cable that operates with the regulator to raise and lower my quarter window has slack and is making a scrunching noise when going down and up. Can I re-attach or otherwise repair the cable or do I have to replace the regulator. If replacing how do I do that after removing the interior trim.
ANSWER: need to replace the whole assembly 2 door 4 door or convertible sebring?
---------- FOLLOW-UP ----------
QUESTION: It is a 2 door convertible.
ANSWER: For a convertible it would be better off for u to let some one that has done it b4 once u install it the adjustments will be a a big deal.
---------- FOLLOW-UP ----------
QUESTION: I did not ask for your suggestion as to my mechanical ability. I asked for instructions as to how to perform the task. If you are not going to answer the questions asked why are you on here. I see that you sign each reply with the fact that you do side work. Is that your main purpose for being on there. If you were not going to give me an answer why did you ask if it was a 2 or 4 door??????
Answerfirst of all my signature is on there for people that live in the atl area that would like for me to do work for them and if u think that I don't answer questions just cauz talk to teh other 20,000 others that I have answered questions for and at no cost to them so what is wrong with getting a little out of it for the time I spend on here?
I asked a 4 door or 2 door because there are 3 different sebrings that were made that year a convertible, a 4 door hard top and 2 door coupe all different in design and how to do things.
Here is the instructions for doing the regulator on teh rear quarter glass.
QUARTER GLASS
NOTE: No access is provided to glass fasteners except if glass is in the full up position. If this position can not be achieved, remove the quarter window module. Refer to quarter window module procedure in this section.
REMOVAL
Raise glass to full up position.
Remove quarter trim panel.
Partially lower convertible top.
Remove fasteners attaching glass to lift channel of quarter window module Quarter Glass
Loosen latch plate hook nut.
Separate glass from vehicle
INSTALLATION
Position glass in vehicle.
Loosely install fasteners holding glass to lift channel of quarter window module.
Lower and secure convertible top.
Tighten latch plate hook nut.
Adjust quarter glass as necessary. Refer to quarter glass adjustment procedure in this section.
Install quarter trim panel.
REAR SEAT BACK
REMOVAL
Remove rear seat cushion.
Remove rear inner seat belt assembly Rear Inner Seat Belt Assembly
Pull bottom of rear seat back forward until seat back brackets clear studs on floor pan Rear Seat Back
Push upward on rear seat back and disengage hooks holding seat back to rear seat back support.
Remove rear seat back from vehicle
INSTALLATION
Position rear seat back in vehicle.
Tilt rear seat back rearward and raise seat back above retaining brackets on rear seat back support.
Lower rear seat back until center loop begins to engage.
Lower rear seat back and push rearward on outboard corners of seat back to engage outboard hooks to brackets on rear seat back support.
Push downward on rear seat back until all hooks are fully engaged into retaining brackets.
Install rear inner seat belt assembly.
Install rear seat cushion
NOTE: Tighten the rear inner seat belt assembly to 40 N·m (350 in. lbs.) torque.
QUARTER TRIM PANEL
REMOVAL
Lower convertible top.
Remove rear seat cushion and rear seat back.
Remove door sill trim panel.
Remove push-in fastener attaching quarter trim panel to door sill panel.
Remove speaker grille Speaker Grille
Remove vertical screws and inboard velcro screw attaching quarter trim panel to inner quarter panel Quarter Trim Panel
Remove screws attaching quarter trim panel to inner quarter panel through the speaker opening.
Remove screws attaching quarter trim panel to inner quarter panel at rear of trim panel.
Remove push-in fasteners attaching quarter trim panel to inner quarter panel at front of trim panel.
Pull trim panel from inner quarter panel and disconnect speaker wiring connector.
Remove quarter trim panel from vehicle
INSTALLATION
Position quarter trim panel on vehicle.
Connect speaker wiring connector.
Install push-in fasteners attaching quarter trim panel to inner quarter panel at front of trim panel.
Install screws attaching quarter trim panel to inner quarter panel through the speaker opening.
Install vertical screws and inboard velcro screw attaching quarter trim panel to inner quarter panel.
Install screws attaching quarter trim panel to inner quarter panel at rear of trim panel.
Install push-in fastener attaching quarter trim panel to door sill panel.
Install door sill trim panel.
Install speaker grille.
Install rear seat cushion and rear seat back
