Small Engines (Lawn Mowers, etc.): Honda 3813 Lawn Tractor, switch jumper, jumper wire

Question
I have a Honda 3813 Tractor and it was given to me by the original
owner.  It has not been started in quite awhile.  I got it to turn over
several times and it fired and made three or four revolutions then
stopped.  It doesn't seem to be firing now.    The owner said the spark
plugs were replaced and the mower used twice then parked.  He said
there were no problems when he stopped using it.  He had a stroke and
had to hire someone to do his yard so his stuff just sat in a shed.  Mower
is extremely clean and seems to have good compression.  Any
suggestions?
Thanks,
Brian Crews

Answer
Hello Brian:

You can View a Breakdown/IPL of the Mower/Engine at this Site Addy, http://hayward.arinet.com/scripts/EmpartISAPI.dll?MF&app=ASP&lang=EN&TF=Mainfram... and Select the Catalog American Honda. PLEASE REMEMBER THAT THE INSTRUCTIONS FOR CHECKING THE SAFETY SWITCHES IS JUST THAT!!! FOR CHECKING ONLY. I NEVER Suggest a Mower be Operated with a Safety Device or Switch Disconnected or Bypassed. Now. On Some Model Mowers you can Simply Unplug the Safety Switch from the Harness. On Other Models you have to Place a Jumper Wire Between the Harness Terminals (on the 4 Post Switch Jumper from Same Color Wire to Same Color Wire). Check the Clutch/Break and the Blade/PTO Safety Switches First. Check the Seat Safety Last. Usually the Seat Safety is Not in the System for Starting the Engine. Just to Ensure Someone is in the Seat when Engaging the Transaxle and/or Blades. If the Safety Switches are Good, then Check the Coil. Remove the Spark Plug. Wrap a Wire Around the Threads and Attach the Other End of the Wire to the Engine Block Turn the Engine and See if the Plug Fires. If No, then Disconnect the Shut Off Wire  at the Control Bracket First, Check for Fire at the Plug. If Still No Fire at the Plug; Then Disconnect the Shut Off Wire at the Coil (usually requires removal of the blower housing) and Check for Fire at the Plug. If No Fire at the Plug , then the Coil/Ign Module is Bad. The Coil/Ign Module to Flywheel Gap is .020in. On Some Model JD Engines, there is a Igniter that Goes Bad and Not the Coil. The Igniter is the Same as an Ignition Module. If the Plug Fires at Anytime During these 2 Checks, then a Safety Switch or Wire May be the Problem. Yes the Engine will Turn Even with a Bad Safety Switch. The Blade Safety is Usually the Cause of this. The Starter Turns and The Engine Doesn't Fire is an Indication of a Bad Coil/Ign Module or a Faulty Blade Safety Switch. The Clutch Safety Prevents the Starter from Engaging so the Mower Does Not Move when the Starter Turns the Engine. The Seat Safety is Designed to Stop the Engine if the Blades are Engaged or the Clutch Safety is Not Engaged when you Leave the Seat. You May Need to Clean the Carburetor since it has been Idle for a Long Period.  Remove, Disassemble and Soak the Carburetor Overnight in Carburetor Cleaner (I Use Gunk). I have Found that Most People can Use a Breakdown/IPL and Disassemble the Carburetor Enough for Proper Cleaning. You Only have to Remove the Bowl, Float Pin, Float and Needle Valve and Any Adjustment Screws that Go Into the Carburetor Body. The Welch Plugs Do Not have to be Removed. Then Soak the Carburetor Body and Parts in a 1 Gallon Can of Gunk Carburetor Cleaner Overnight. The Can has a Parts Tray Inside it for the Small Parts. Once the Carburetor and Parts are in the Cleaner, you can Replace the Lid for Safety and to Prevent Accidental Spillage. Then Blow Out the Passages with Compressed Air. Install New Parts if Required. Hope this Helps. I am Here if You Require More Assistance. Let me Know What Happens, Please. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 9pm EST (US). My New Day Starts then. Thanks.

Respectfully

John