Questioni have a 98 chrysler concorde that the battery goes dead after sitting for 9 hours Ihave checkedevery thing that Ican think of
AnswerHi Rhonda,
I think you have a short somewhere in the wiring or a component is staying energized when it shouldn't be. Here is how I responded last week to a similar question:
"The best way to find what is causing the draining is to obtain a volt-ohm meter at an electronics store or an auto parts store, or borrow one from a friend. (You can for a little more money use a meter that also measures current, amps, and use it the same way as I will now describe except you will be trying to find fuses that when removed reduce the reading (less current flow) on the dial). You should be able to get one for under $20. Then you disconnect the clamp from the "-" or "neg" post of the battery, then remove the "+" or "pos" clamp. Then put the two test leads of the meter on the two clamps (one lead on each clamp) with the meter set to read ohms. It should read something less than infinite, but you would like it to read more that 100 ohms and ideally much more ohms than that, which would mean there was no source draining away the charge. If instead you find that it reads only 5 or 10 ohms that means there is a component that is draining the battery. (If you intend to measure current, then the battery needs to be in play so you would just remove one battery clamp (the - post one) and insert the leads of the amp meter between the clamp and post that you have disconnected the clamp from).
The procedure to find out the drain source is to disconnect each of the fuses (start with fuse #19 which you find by removing the end cap of the dash by the driver's door and looking in the opening. That is the fuse which is connected to the battery even when you have the engine off. See if that causes the resistance to jump up). Write back and tell what how much the reading increased, and if it is significant I can tell you everything that is 'on' that fuse so you can similarly check each out to find out which is drawing too much current.
If not, then go to the larger fuses in the power distribution center box under the hood, it is long and thin) that are assigned to a specific circuit in the car, one at a time, and see if the meter reading moves toward infinity (ohms) or decreases (amps) as the result. If there is no change in the reading of the meter, then replace the fuse and move to the next one in the distribution center box and see if it causes an increased reading, etc. When you find one (or more) such fuses that when removed caused the reading of the meter to go up significantly, then look for the label on the fuse box for that fuse.
Then if the fuse isn't labelled as to its purpose write me back and I can tell you which fuses/circuits the fuse in the distribution center powers up in the secondary fuse box that is behind the dash. Then you will go to the behind the dash box and do the same thing, and when you find the smaller fuse that also raises the resistance (decrease the current) when pulled you will begin to unplug each of the electrical items that are powered by that fuse and keep checking until you find the item that causes the reading to go up again. That is the faulty component that is causing your problem.
You will want to do these measurements with all the doors closed so that no lights are "on" and the car is sitting just as it is when you have it shut down. Be careful not to change anything about the car doors/lights (always close the doors before reading the meter) while you are doing this testing or none of it will make any sense.
This is something you can do yourself and save labor costs by so doing. If you find a fuse that when removed causes the reading to rise significantly, tell me what the number of that fuse is and I will tell you what to do then to solve that problem specifically (how to unplug the suspected faulty item).
Whenever you go to reconnect the battery, always put the + post clamp back on first, then put on the - post clamp. The reverse is true when you disconnect the battery (as I described to you at the start). It is done that way for safety so you don't accidentally short the battery and get a burn.
So let me know if it is fuse 19 or what fuse #'s in the power distribution center are causing signicant changes in the meter reading and if you can find an associated fuse under the dash that does the same thing let me know that too.
Roland
