QuestionOK so disregard the first question about getting the door panel off. The problem is the power window mechanism. Upon rolling it up (thank goodness) I heard a loud pop like a strap breaking followed by what sounded like a piece of plastic falling so I knew that it was broken. Now that the panel is off I can see that the wires are twisted up with the broken strap. Can I just replace the strap or should I just replace everything? And do you have any clues on how to do that?
Thanks
Answeryeah I have a clue or I hope I would being a Chrysler tech for 11 years =)first part will be the trim panel the second will be the regulator and motor assembly I would get a whole new assembly.
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (C-4755), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.
POWER WINDOW MOTOR
WARNING: DO NOT HAVE ANY HANDS OR FINGERS IN AREA WHERE THEY CAN BE PINCHED BY SMALL MOVEMENTS OF REGULATOR LINKAGE.
REMOVAL
Disconnect and isolate the battery negative cable.
Remove front door trim panel and sound pad. Refer to Group 23 Body, for Front Door Trim Panel Removal and Installation.
Tape the window in its existing position to remove its weight from the regulator system.
Cut and remove the tie wrap at the window motor. Its no longer required.
Disconnect window motor wire connector from door harness.
Remove screws and nuts holding window motor to the inner panel.
Remove the motor from the door inner panel, let it hang from the cables.
With the cables still attached to the failed motor, Install the replacement motor to the door inner panel. Tighten down the screws and nuts to 3.4 to 4.5 N·m (30 to 40 in. lbs.) of torque.
Separate the failed motor from regulator by:
Removing the drum cover plate.
Lift the cable guide off the motor, the drum with cables, will be lifted off simultaneously Power Window Motor Removal
CAUTION: Do not allow the drum to separate from the cable guide, by dropping drum or letting the cables unwind.
INSTALLATION
Install the cable guide and drum into the replacement motor
CAUTION: The drum may require a slight rotation to install onto the motor drive shaft. Rotate the drum with the use of needle nose pliers or a similar tool. If, the drum does not align with the motor shaft by a slight rotation, then, the glass should be lowered a small amount approximately 1 to 2 inches. The drum will rotate when the glass is lowered. Lowering the glass will require assistance of a second person.
install the replacement cover plate onto the replacement motor. Crimp toy tabs.
Connect the wiring harness to the window motor connector.
Remove the tape holding the window in place and test window operation.
Re-assemble remaining parts in reverse order as above.
the regulator assembly will already have a new motor if u need a new assembly.
