QuestionQUESTION: I noticed a large amount of smoke coming out of the valve
cover breather tube. I have a loss of power, backfiring,can't
throttle without stalling or turn the off the choke without stalling. The carb is rebuilt all holes checked out clean.
does this need a valve job ?
ANSWER: Hello Thomas:
>>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ and Select the T. Then Select Tecumseh. Then Select Don't have Part Numbers. Then Enter the Model Numbers . Then Select your Model and Download the File for Online Viewing.
>>From your Description it Sounds like a Damaged Flywheel Key or the Valve Require Adjusting and/or Seating/Lapping.
>>The Following is the Instruction File I Made for Removing the Flywheel from Most Mower Engines for Replacing the Flywheel Key, the Stator/Charging Coil/Magneto and the Point Set on Older Engines without Electronic Ign Coils.
>>It is the Basics and if you have a Question, Please Ask. Any Input to Make this File Better is Appreciated.
>>***Disconnect the Coil Wire from the Spark Plug. Remove the Blower Housing (metal engine cover).
>>Remove the Coil.
>>Remove the Flywheel Nut or Starter Cup (Depends on the Model).
>>Now Attach a Steering Wheel Puller to the Flywheel Using the Threaded Holes in the Flywheel.
>>Tighten the Puller.
>>Now Hit the Puller with a Hammer. Repeat this Procedure Until the Flywheel Pops Up or can be Lifted Off the Crankshaft.
>>On Some Models you Can Not Use a Puller and and the Jaws of a Standard Puller will Not Fit. On these Type Engines you can Use a Pry Bar and a Pipe Cap that is Slightly Larger than the Crankshaft. Place the Pipe Cap Over the Crankshaft to Protect it. Place the Pry Bar Under the Thick Section of the Flywheel and Pull Up Against the Flywheel.
>>**BE CAREFUL DO NOT PUT A HOLE IN THE BLOCK UNDER THE FLYWHEEL** >>Now Hit the Pipe Cap that is on the Crankshaft (covered with the Pipe Cap). Repeat the Procedure Until the Flywheel can be Lifted Off the Crankshaft.
>>*** Be Sure you have the Flywheel Torqued to the Proper Torque (I require the Model and Spec/Type Numbers Off the Engine to Provide the Proper Torque) and Set the Coil Gap to .020in..***
>>The Following is a Basic Instruction File for Setting the Valve Clearances on Non OHV Engines. If you Provided me with the Correct Make and Model of the Engine then the Specifications are Included. If Not I May be Able to Provide the Specifications if you Supply me the Make and Model Numbers.
>>The Most Common Clearances are Listed for this Engine in the Following File. Thanks. Any Input is Appreciated.
>>On this Model Engine I Usually Suggest Reseating the Valves if the Valve Clearance Requires Adjusting.
>>**Remove the Carburetor and the Crankcase Breather/Vent and the Valve (Stem) Cover so you have Access to the Valve Stems, Springs and Keepers.
>>Set 1 Cylinder (on Twin Cylinder Engines) to TDC on the Compression Stroke. Using a Blade Style Feeler Gauge, Check the Clearances. The Intake should be .005in - .007in and Exhaust .008in - .010in. If the Feeler Gauge will Not Slide Between the Valve Tip and the Tappet, then you Must Reset the Clearances.
>>**You Will Require a Small Engine Valve Spring Compressor to Remove the Springs and Keepers from the Valve Stems.** Some Engines Use a Valve Keeper that is like Automotive Keepers (2 Cone Shaped Keepers that Set in the Valve Retainer/Rotocoil Assembly)and the Other Style is a Slotted Retainer that is Moved (once the Valve Spring is Compressed) to the Larger Opening in the Retainer and the Retainer Slips Over the Valve Stem Tip for the Valve to be Removed.
>>Remove the Heads.
>>Set 1 Cylinder so the Piston is at TDC on the Compression Stroke And Check the Clearances Between the Valve Stem Tip and the Tappet. The Clearances are as Follows: Intake Valve Clearance is .005in - .007in and the Exhaust is .008in - .010in.
>>You have to Lightly Grind the Valve Stem Tip and Place the Valve Back Into the Engine (you can Hold the Valve Seated by Hand) and Check the Clearance Until you Reach the Required Clearances.
>>**++** For this Engine Model I Suggest you Reseat the Valves while you are Setting the Correct Valve Clearance. For this you will Need a Small Valve Seat Suction Tool. This can Usually be Purchased for $10.00us and has a Suction Cup that Hold the Valve Head so you can Turn the Valve Back and Forth and Dress up the Valve Seat. Valve Grinding Compound is Approximately $5.00us a Tube and a Tube Last the Shop About a Year. It Doesn't Take a Lot to Reseat 1 Engine.**++**
>> Once the Valve Clearances are Reached and the Valve Seat is Nice and Dull; Re-Install the Valves on that Cylinder and Turn the Other Cylinder to TDC on the Compression Stroke and Set that Cylinders Valve Clearances.
>>Once that Cylinder is Set, then Assemble the Engine.**
>>This Web Page; http://www.affordablegokarts.com/va
lve-lapping.php has a Fairly Good Description and Instructions on Valve Lapping and a Good Explanation of what to Look for when Seating the Valves.
>>If this Engine has the Point and Condensor Under the Flywheel, then the Valve Clearances are; Intake .008in and Exhaust .0012in
>>If this Engine has the Electronic Ign Coil/Magneto, then the Valve Clearances are; Intake .004in and Exhaust .008in
>>If you Hit a Snag or this Does Not Correct the Problem, I Hope to be Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Be Safe and Happy. Thanks.
Good Luck
Respectfully
John
PS: I am Allowed to Answer 3 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. All Follow up Questions are Accepted at Any Time. Comments and Ratings are Greatly Appreciated. Thanks.
Respectfully
John
---------- FOLLOW-UP ----------
QUESTION: I'm going to start with the valves since I'm 99% sure there is no problem with the fly wheel key. when I opened up the cover there was a puddle of oil is this normal.
Thanks in advance.
ANSWER: Hello Again Thomas:
>>A Small Amount of Oil in the Bottom of the Crankcase Breather/Vent is Normal.
>>If you Shake the Crankcase Breather, Does it Rattle?
>>If No, then
>>Open and Clean the Oil from Inside the Crankcase Breather before you Complete the Valve Seat and Clearance Repairs.
>>Remember that you may have to Grind the Valve Stems before and After you Lap the Valves to have the Correct Clearance.
>>As Always, If you Hit a Snag or this Does Not Correct the Problem, I Hope to be Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Be Safe and Happy. Thanks.
Good Luck
Respectfully
John
PS: I am Allowed to Answer 3 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. All Follow up Questions are Accepted at Any Time. Comments and Ratings are Greatly Appreciated. Thanks.
Respectfully
John
---------- FOLLOW-UP ----------
QUESTION: also there was oil in the Piston cylinder. should I change the rings ? and how do I know if the cylinder should be honed
Answer>>Hi Again Thomas:
>>Oil in the Cylinder when the Head is Removed is Normal as Long as it was Not an Excessive Amount.
>>You have to Remove the Piston from the Cylinder to Check the Rings.
>>If you are going so Far as to Check the Rings, then
>>I Suggest you Hone the Cylinder and Replace the Rings.
>>Anytime a Piston is Removed from the Cylinder the Cylinder has to be Honed in Order for the Rings (Old or New) to Seat/Reseat.
>>As Always, If you Hit a Snag or this Does Not Correct the Problem, I Hope to be Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Be Safe and Happy. Thanks.
Good Luck
Respectfully
John
PS: I am Allowed to Answer 3 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. All Follow up Questions are Accepted at Any Time. Comments and Ratings are Greatly Appreciated. Thanks.
Respectfully
John
