Small Engines (Lawn Mowers, etc.): Briggs & Stratton 6.5 hp Intek Kick Back on attempted start., twin cylinder engines, briggs stratton

Question
I have a Scotts LM21SW 21" lawnmower with an Intek Briggs & Stratton 6.5hp engine. I can not get the engine to start post a full carb clean and fresh everything in tune parts. The engine will occasionally give a sign of life then will give 2 or 3 rotations and die. The pull start also gets occasionally terrible pull back on the handle with it wanting to rip it back and yank my arm off.
I have been playing with it for 2 weeks. I have soaked and blown out the carb and all jets.

Answer
Hello Gregg:

Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer Questions from the Question Pool when I am Not Answering Questions here or at the Other Site I Answer Questions at. Also, I am on Vacation and had a Few Minutes to Answer a Few Questions. From your Description it Sounds like the Valve Clearances Require Adjustment. Not having the Engine Model Numbers, I am Including Both the Instruction Files for the OHV and Non OHV Engines. 1- The Following is a Basic File I made for Setting the Valve Clearances on OHV Engines. Any Input is Appreciated. **I Do Not Use the Setting Called for by the OEMs. I have Found that the Following Works Best. Remove the Valve Cover (on the Dead Cylinder for Twin Cylinder Engines). Set the Cylinder you are Setting the Valves on to Top Dead Center on the Compression Stroke When Setting the Valve Clearance. Now Loosen the Valve Adjuster Locks and Set the Intake Valve Clearance to .004in -.006in and the Exhaust to .005in - .007in. I have had Better Performance Out of the Mowers and Less Burnt Valves Using these Settings. Be Sure the Piston is at TDC on the Compression Stroke.** On Some Engines you can Us a Straightened Coat Hanger and Feel the Piston. Be Careful and Dont Jam the Wire in the Cylinder. Usually the Piston will Push the Wire Out of the Spark Plug Hole with No Problems.  2- The Following is a Basic Instruction File for Setting the Valve Clearances on Non OHV Engines. Any Input is Appreciated. On this Model Engine I Usually Suggest Reseating the Valves if the Valve Clearance Requires Adjusting. The Following is a General Instruction File for Setting the Valve Clearance on Non OHV Engines. **Remove the Carburetor and the Crankcase Breather/Vent and the Valve (Stem) Cover so you have Access to the Valve Stems, Springs and Keepers. Set 1 Cylinder to TDC on the Compression Stroke. Using a Blade Style Feeler Gauge, Check the Clearances. The Intake should be .005in - .007in and Exhaust .008in - .010in. If the Feeler Gauge will Not Slide Between the Valve Tip and the Tappet, then you Must Reset the Clearances. **You Will Require a Small Engine Valve Spring Compressor to Remove the Springs and Keepers from the Valve Stems.** Some Engines Use a Valve Keeper that is like Automotive Keepers (2 Cone Shaped Keepers that Set in the Valve Retainer/Rotocoil Assembly)and the Other Style is a Slotted Retainer that is Moved (once the Valve Spring is Compressed) to the Larger Opening in the Retainer and the Retainer Slips Over the Valve Stem Tip for the Valve to be Removed. Remove the Heads. Set 1 Cylinder so the Piston is at TDC on the Compression Stroke And Check the Clearances Between the Valve Stem Tip and the Tappet. The Clearances are as Follows: Intake Valve Clearance is .005in - .007in and the Exhaust is .008in - .010in. You have to Lightly Grind the Valve Stem Tip and Place the Valve Back Into the Engine (you can Hold the Valve Seated by Hand) and Check the Clearance Until you Reach the Required Clearances. **++** For this Engine Model I Suggest you Reseat the Valves while you are Setting the Correct Valve Clearance. For this you will Need a Small Valve Seat Suction Tool. This can Usually be Purchased for $10.00us and has a Suction Cup that Hold the Valve Head so you can Turn the Valve Back and Forth and Dress up the Valve Seat. Valve Grinding Compound is Approximately $5.00us a Tube and a Tube Last the Shop About a Year. It Doesn't Take a Lot to Reseat 1 Engine.**++** Once the Valve Clearances are Reached and the Valve Seat is Nice and Dull; Re-Install the Valves on that Cylinder and Turn the Other Cylinder to TDC on the Compression Stroke and Set that Cylinders Valve Clearances.  Once that Cylinder is Set, then Re-Assemble the Engine.** If you Hit a Snag or this Does Not Correct the Problem,  I am Here if You Require More Assistance. Hope this Helps. Let me Know What Happens, Please. May the All Mighty Bless You and Yours. Thanks.

Good Luck

Respectfully

John

PS: I am Allowed to Answer 10 Questions a Day. If you See I am Maxxed Out, then Try Submitting your Question at or Just After 8pm EST (US). My New Day Starts then. Thanks.

Respectfully

John